LOCAL CONVERSION

Convert MIDI to MP3.

Choose a MIDI file, select a synthesized sound, then preview and download MP3 or WAV. Local processing; pitched notes only.

No file selected

Files are processed on this device.

Turn note instructions into an audio file

A MIDI file tells an instrument which notes to play. It does not contain the singer, piano recording, or original mix. To make an MP3, this page reads those note events, supplies a synthesized sound, and encodes the resulting waveform. The sound you choose here therefore changes the timbre.

Choose a .mid or .midi file, select a sound, and convert. Listen to the WAV preview before downloading the MP3. For MIDI to WAV, use the second download from the same render; changing the output container does not restore an original recording.

MIDI to MP3: notes need an instrument: MIDI events, then Local synthesizer, then WAV / MP3.
The selected sound supplies the timbre; it is not the original recording.

What this renderer actually keeps

Midilot reads Standard MIDI formats 0 and 1 with quarter-note timing. The event reader combines the tracks on one time line, applies tempo changes when translating ticks to seconds, and pairs note-on with note-off events. A note-on with zero velocity closes a note rather than starting a silent new one. These are concrete rules in this page's own reader.

The renderer follows sustain controller 64: a released key can remain sounding until the pedal is released. The separate key-release time remains in the parsed record. That distinction matters if a long piano tail sounds right but would be misleading as a long written note in a score.

Both sound choices are synthesized pitched tones. Program changes, SoundFonts, pitch bends and instrument-specific articulations are not reproduced. Drum-channel notes are skipped and the status reports the skipped count; a drum-only file is rejected. The output is mono PCM at 22,050 samples per second. The WAV is 16-bit; the MP3 encoder setting is 128 kbps. These settings describe this implementation, not a quality ranking.

One MIDI rendered with two synthesized sounds and combined locally
One source melody can be rendered with two sounds. See the paired layering example and measured MIDI results.

Two original files you can check

The eight-note MIDI has C4, D4, E4, G4, A4, G4, E4, C4 at 120 BPM. Each note starts one quarter-note beat after the previous one and stays keyed for three quarters of a beat. The last key release is at 3.875 seconds. The renderer allocates a further half second for its release tail, so this example tests note timing separately from audio-file duration.

The tempo-and-sustain MIDI is a different test. C4 starts at 0 seconds, its key is released at 1 second, and the pedal holds it until 1.5 seconds. E4 spans 1–2 seconds. At beat 4, the tempo changes from 120 to 60 BPM, so G4 lasts from 2–3 seconds. A render that treats every tick as the same number of seconds cannot follow that sequence.

These files were programmed for Midilot, not taken from a performance. Their expected note events and hashes are in the reference record. Use Try original sample for the melody, or download and choose the second file. Listen, compare the times and check that the tail releases; neither input is a benchmark of all MIDI instruments.

ORIGINAL MIDI CONTROLS · 22 OCTOBER 2026

Why are the drums missing from my rendered audio?

This renderer skips drum-channel notes. Our original mixed MIDI returned one pitched note and reported one percussion note skipped. A second file containing only the same drum event was rejected. MP3 and WAV are two exports of the same pitched render; switching between them cannot add a drum instrument.

We programmed a format-0 control with C4, MIDI note 60, on channel 1 and note 36 on channel 10. Both start at zero and end after 480 ticks. The file sets 480 ticks per quarter note and 500,000 microseconds per quarter note: 480 / 480 × 500,000 / 1,000,000 = 0.5 seconds. The drum-only control removes C4 and leaves that second event unchanged. Our parser uses zero-based channel indexes, so channel 10 is stored as 9. These are original event instructions, not recordings or examples of a natural drum sound.

Actual mixed input: one pitched note rendered and one percussion note skipped. Actual drum-only input: rejected with no new audio.
Two original MIDI controls through the same Soft sine renderer. The result describes this implementation, not the quality of a drum instrument or another converter.

What the actual downloaded files contain

The mixed input produced a 44,144-byte WAV and a 17,136-byte MP3 through the production page. Independent WAV inspection found mono 16-bit PCM, 22,050 frames at 22,050 samples per second: 22,050 / 22,050 = 1 second. The PCM contained nonzero samples. The programmed note ends at 0.5 seconds, while the renderer allocates another 0.5 seconds to the output buffer. That allocation is not evidence that a tone remains audible for the entire extra half second.

An independent decoder read the actual MP3 to its end and identified a mono 22,050 Hz stream at 128 kb/s. The browser WAV preview also entered playback without a media error. Those observations establish usable audio outputs for this fixture; they do not measure a reproduced instrument, confirm a natural performance, or turn a percussion event into pitched music. The original input events, output hashes and inspection details are available below.

The drum-only run displayed “This MIDI contains only drums; choose a pitched track.” and produced no new audio. During this check we also found that choosing another MIDI left the preceding preview and download links visible until Convert was pressed. We corrected that state handling: selecting a file now stops the old preview and removes its download links, and a rejected conversion clears them too. The renderer’s treatment of drum events was not changed.

Original events, actual outcomes and output hashes · Rebuild the two exact MIDI inputs

Can I recover the missing drums by choosing WAV instead of MP3?

No. Both downloads use the same pitched-note render. Use a renderer with a drum kit or the instrument setup in your music software when you need the drum part. Changing the filename or export container cannot supply an instrument this renderer omits.

Questions before exporting

Can I convert MID to MP3?

Yes. MID is the usual .mid filename extension. Choose it above. The reader still checks the actual MIDI header; renaming an audio file to .mid will not make it a MIDI sequence.

Does converting MIDI to MP3 preserve a recorded voice?

No. This page supplies a synthesized tone for the note events. Use the original audio if you need the recorded voice or instrument sound.

Why is a file rejected?

Format 2, SMPTE timing, malformed event lengths, files over 10 MB, more than 5,000 notes, and playback over five minutes are rejected. Very dense overlapping parts can also exceed the renderer's work limit. Export a shorter pitched part from your music software and retry.

What the original-sample run produced

On 14 October 2026, Try original sample returned eight pitched notes and a playable local WAV preview. The rendered PCM contained 96,469 samples at 22,050 samples per second: 96,469 / 22,050 = 4.375011 seconds. The original notes end at 3.875 seconds; the remaining half second is allocated for the release tail. This is one controlled input, not a general speed test.

The matching MP3 contained 71,053 bytes. An independent decoder read it to the end as mono MP3 at 22,050 Hz with a 128 kbps audio stream. MP3 frame padding means its playback boundary can differ slightly from the PCM boundary. Check the musical events and release separately from the encoded container size.